How to Build a DIY Nightstand


The do-it-yourself initiatives that soar to the highest of my checklist at all times appear to be those that add extra operate to our residence. If a construct guarantees to place wasted area to good use or carry group to a cluttered space, I discover myself feeling additional impressed.

PREP STEPS. Jenn makes use of a miter noticed to chop the night time desk’s 2×2 legs, in addition to its 1×2 crosspieces. A desk noticed is useful for reducing the edges and shelf, however a round noticed with a information works, too.
Mock Tuna

So once I observed charger cords, books, and miscellaneous objects accumulating on my bedside desk, I made a decision it was time to make one thing that would supply extra storage than I presently have. And whereas drawers are usually not sometimes thought-about a straightforward construct, the pocket-hole meeting methodology I used affords an excellent resolution for novices.

Because of its beneficiant footprint, two stacked drawers, and backside shelf, my nightstand feels neat and tidy when it comes time to end up the sunshine. Up forward: what it’s worthwhile to know to construct considered one of your personal.

Getting Began

Illustration of how to build a nightstand

Peter Sucheski

The usual top for a nightstand usually ranges from 24 to twenty-eight inches. Whereas trendy furnishings design favors low-slung aspect tables, I like a standard nightstand to sit down 1 to 2 inches increased than the highest of the mattress.

For alongside my very own mattress, I designed this aspect desk to be 30 inches tall; that approach, the studying lamp casts its mild down onto my e book, and its swap is inside straightforward attain. To measurement the nightstand up or down, you may merely regulate the peak of the two×2 legs, whereas sustaining the space of the underside shelf to the ground.

Instruments

Supplies

Minimize checklist

  • 2×2 legs – 4 @ 29 1/2 inches L
  • 1×2 crosspieces – 4 @ 12 inches L
  • 1×2 crosspieces – 4 @ 20 inches L
  • plywood sides – 2 @ 3/4” x 12”W x 12 1/2”L
  • plywood prime – 1 @ 3/4” x 24 1/2”W x 15 3/4”L
  • plywood shelf – 1 @ 3/4” x 20”W x 12” L
  • plywood drawer sides – 4 @ 3/4” x 4”H x 13 1/4”W
  • plywood drawer-box fronts and backs – 4 @ 3/4” x 4”H x 17 1/2”W
  • plywood drawer bases – 2 @ 3/4” x 17 1/2”W x 11 3/4”D
  • plywood drawer fronts – 2 @ 3/4” x 5 1/4”H x 19 7/8”W

Completed Dimensions: 24 1/2”W x 15 3/4”D x 30”H

Steps for Constructing a DIY Nightstand

Step 1: Prep the components

Prepping the parts

Mock Tuna

Following the reduce checklist above, reduce the items to size. Use the pocket-hole jig to drill two holes on the ends of the back and front items for the drawers and every 1 ×2.

Drill further pocket holes alongside all edges of the plywood shelf and every drawer base, and alongside the highest and aspect edges of the plywood sides.

Step 2: Assemble one plywood aspect

Assemble one plywood side

Mock Tuna

Place a 12-inch 1×2 between two 2×2 legs, 12½ inches down from the tops of the legs. Connect it with glue and pocket-hole screws. Place a plywood aspect on prime of the 1 ×2, its backside edges flush and its prime edge supported; safe with glue and pocket-hole screws.

Step 3: Connect a 1×2 crosspiece

Attach a 1x2 crosspiece

Mock Tuna

Mark a line 5 inches from the underside of every leg. Place a 12-inch 1×2 between the legs, propped up on 3/4-inch blocks and flush with the legs’ inside faces. Utilizing the bar clamp, safe it with glue and pocket-hole screws. Repeat Steps 2 and three for the second aspect.

Step 4: Set up the shelf

Install the shelf

Mock Tuna

Glue and pocket-hole-screw 20-inch 1×2s to the back and front edges of the ply-wood shelf, flush with its prime. (The plywood will cowl one of many two pocket-screw holes at every finish.) With a aspect meeting mendacity flat, inside face up, glue and pocket-hole-screw the shelf flush with the highest fringe of one of many decrease 1×2s. Flip the workpiece over, and repeat on the opposite aspect. Glue and pocket-hole-screw two 20-inch 1 ×2 crosspieces between the edges, flush with the higher 1 ×2s.

Step 5: Connect the highest

Attach the top

Mock Tuna

Place the workpiece the other way up on the plywood prime, centered alongside the highest’s width and flush with its again edge. Drive pocket-hole screws by the plywood panels and into the highest. Iron on veneer tape to complete the perimeters; trim extra.

Step 6: Assemble the drawer packing containers

Assemble the drawer boxes

Mock Tuna

Glue and pockethole-screw a plywood back and front to a drawer backside so they’re flush with its underside; glue and pocket-hole-screw the drawer sides to the underside, entrance, and again. Repeat. Sand each assemblies clean, and paint all of the items.

Install the drawers & add drawer fronts and pulls

Mock Tuna

Step 7: Set up the drawers

Separate the slides and screw one half to every drawer field, centered vertically and flush with the entrance edge. Connect the correspond – ing components contained in the workpiece. Insert the drawers, rejoining the 2 components of every slide.

Step 8: Add drawer fronts and pulls

Mark and drill holes for the pulls within the utilized drawer fronts, then tack them to the drawer fronts with screws by the pull holes. From contained in the drawers, drive screws by the drawer fronts and into the utilized fronts. Take away the short-term screws, drill holes by the drawer packing containers, and screw on the pulls.



Posted by :www.thisoldhouse.com

Corahome

Welcome, you are reading the article How to Build a DIY Nightstand published date 2022-08-16. Thank you for visiting Corarchitecture

Leave a Comment